1 x Left Tower 1 x Right Tower 1 x Base 1 x Headphone Hook 3 x Gears 4 x Spacers 2 x Base Connectors 24 x Washers 24 x 3M Screws 1 x Hex Key
First assemble the base. Attach the 2 base connectors to the base its self. The smoother portion of the base is the bottom. 4 bolts push through the center of the base and connect to the adapters like the in the picture below. Washers are optional on the underside of the base.
Next pick either the left or right tower portion and start to assemble it as seen in the pictures below. Make sure to use washers to give it that contrasted look!
Once you have the tower portion all assembled you can connect it to the base. The base can be connected with the two gears in front, or one gear in front. Both ways are very stable. See the orientation of the base below in two different finished headphone stands.
This is a really simple install. With your rear hatch door fully open, locate your third brake light. Notice there is a gap between the light housing and the glass window. Slide the brake cover in between the glass and your light housing. You want to make sure the text reads properly if light were to shine through it. It will not fit backwards (unless you force it, it won’t fit well).
If your brake light cover does not use text, you can easily line the bottom tabs (see picture) with the tab locations in my design.
The top portion of the cover (when looking at the illustration above) is designed to slip into your weather strip. It might be easier just to watch my video below! The red arrows signify where the cover is securely held when fully installed.
Much like the original accessory, this installs on the underside of the spare tire cover. You simply remove it and flip it over to show the anchor points. Assuming you did not have the original kit, you will find 4 mounting points near the inside corners of the cover.
Notice in the illustration above that the supplied nut needs to slide under the bracket. I have provided a tool to make that part easier. Just place the nut on the tool and align it with the factory hole. Orientation of the adapters wont completely matter with the reproduction of the OEM clips. However, I did design them to align flush with the design of the cover. If you are installing the aftermarket adapters orientation will matter. You should be supplied with 2 versions of the clips, one is just a mirror of the other. Because the legs are slightly offset the mounting point is not perfectly center where the adapter secures to the cover. When you align the aftermarket adapters you want the protruding portion to be closest to the center of the cover. I have included a video that should make it much easier to understand.
I have been told that many of us have warped covers as we haul things and our Elements age. If this is true, the legs may be difficult to attach. We have found that connecting them on the flat surface while stepping on the center (to correct the warp) will allow the legs to connect.
I should also mention currently Walmart has the preferred legs on sale for 28 dollars. This price is obviously subject to change. Sometimes amazon.com carries the legs too, currently they only sell them through 3rd party vendors (and that is always a pain, I don’t recommend using amazon at this time.).
I made my best efforts to replicate the original accessory that takes the spare tire cover and turns it into a camping or tailgating table. The accessory Honda offered has been discontinued. This makes it very difficult to locate a set of legs. Sometimes you will spot them for sale second hand. Usually the person offering this item knows how rare it is, and the price reflects this. I really liked the idea of creating a set of legs for myself, because I didn’t buy my first Element until late 2016. I was too late to buy any of these accessories new.
I researched the legs, and read a post somewhere that a set of Coleman legs were really similar. They supported the table, but didn’t connect. I hoped if they were close enough I could develop an adapter to solve this issue and at least have a similar set for my own adventures.
You can see the original set of legs, they have a socket where a plastic adapter inserts to secure to the top. The Coleman legs were designed to connect to a pole, similar to a Lego hand. I was pleased to see that the Coleman legs did the movement. 3D printing something designed to go through stress to function is not ideal. My final design accounts for the slight offset as well as allows the legs to connect no matter the direction the ‘Lego’ hand approaches it. I also had to account for a limited height so the adapter would not impede with the final resting place of the table top (covering the spare).
In the picture above, comparing the original clips to the aftermarket adapters I designed you can see how my design does not allow for movement or flex. That is because it is not needed. its a stationary socket that the legs are designed to grip. Because of this, the aftermarket design is superior.
The Coleman legs have a wider footprint. This makes them more stable. They are also constructed with steel. One of the best parts is that they have a pin in place to stop the sliding mechanism when they are fully extended. With the original legs you just have to guess as you line it up. The Coleman legs open so easily too. The original legs are pretty difficult to spread open. You could easily open the Coleman legs with one hand.
So at the end of the day, both legs accomplish the same thing. However, I feel I am selling a superior product.
Steel vs Aluminum
Adapter is not prone to snap off
Reasonable cost (~60 depending on Coleman’ cost)
Wider stance – Table will be more stable and less capable of buckling under stress.
I developed a replaceable cup holder insert that fits certain later models of the Honda Element as well as the 1st generation Honda Pilot. If you have a Honda Element SC model or a 2009+ model, it will fit in your vehicle. The reason I created this product is because I could not fit my Nalgene style water bottle into my original cup holder. So I would have it laying down in the passenger seat. Sometimes I would not have the lid completely on, and that would result in a wet seat.
So I created this for myself and was very pleased with the results. It worked, and it was simple. I shared this on a Facebook group for Element owners, and it was quite popular. Many people asked it they could also have one, but i was just not setup for that sort of thing. Enough people started to ask, and someone in a similar situation suggested I start an Etsy page. So this is the product that started my Etsy store.
So its a direct snap in replacement that comes in 3 different styles (standard 2 cup, single with phone slot, and deluxe). The two are pretty self explanatory, but with the deluxe I tried to make something for the daily commuter. It has a place to organize change, two pen holders, a phone holder as well as the larger cup opening. If your thermos of choice still has a handle, you’ll be limited to the 2 cup version. Otherwise, you are able to try out the others. Also, they stack nicely and can fit in your glove box when they are not in use. So just owning one is not necessary. I have printed them in a few different colors, Most people request black.
I print this in ABS at 50% infill. I am trying to create a long lasting product knowing that these things will likely never be injection molded. I have to be realistic. I created a replacement part for a car that has not been in production for 8 years now. Additive manufacturing is fantastic for rapid prototyping, and for a small batch of products, its a perfect solution.